If the gibberish is different each time, and you are sure that the device is trying to send the same data each time, you don't have a baud rate issue.
If sometimes you get what looks like a valid error number, that rules out problems like level shifting (e.g. using TTL levels instead of RS232).
You might want to check voltage levels or see if there could be something introducing noise (like two machines trying to talk to the same device at once).
A weak power supply could cause noise in the line, especially if a current-hungry motor or heater was getting turned on or off as the message was sent.
If one device is sending Unicode to a device that expects ASCII, that could be a problem, but you said the garbage is different each time.
If one device is sending data faster than the receiving device can take it, you can get garbage. The sender may be expecting hardware flow control and your cable doesn't have those wires connected.
Use a full cable, or switch to software flow control.
Some devices send boot messages at one baud rate and then switch baud rates to communicate. But again, the garbage would be the same each time.
On Tue, Apr 7, 2020 at 2:42 PM Dakota Hamill <dkotes@gmail.com> wrote:
Hello all. Asking for some troubleshooting help, DIY Analytical chemistry, close enough for DIYBio as I'm at my wits end messing with cables and baud rates.--Stringing together an HPLC system and could type out a story or attach my sweet MS Paint diagram of how things are connected, but the real question is, what would cause a machine to respond with gibberish characters when asked it's name in a command line as seen in the picture below?GSIOC may be Gilson's own serial communication setup, and I know next to nothing about coding etc.However when I ping the liquid handler or the UV/Vis machine with a "%" command, it returns the modules name and software version number, when I ping the HPLC Pumps with the same command, it returns a different array of gibberish characters each time, or an #error.I've set baud rates on everything to 19200 which it's defaulted to, or Externally set on the HPLC pumps, no difference.Perhaps a long shot but didn't know if people that new older serial port machines knew if random giberish was coming up, it's just a bad baud rate somewhere along the line, or something might be out of order.
-- You received this message because you are subscribed to the Google Groups DIYbio group. To post to this group, send email to diybio@googlegroups.com. To unsubscribe from this group, send email to diybio+unsubscribe@googlegroups.com. For more options, visit this group at https://groups.google.com/d/forum/diybio?hl=en
Learn more at www.diybio.org
---
You received this message because you are subscribed to the Google Groups "DIYbio" group.
To unsubscribe from this group and stop receiving emails from it, send an email to diybio+unsubscribe@googlegroups.com.
To view this discussion on the web visit https://groups.google.com/d/msgid/diybio/CAGdeWmTY30arDFKBpW8-J_6cwNkx0smT9%3DPD9Ce7T-XrG6vmFg%40mail.gmail.com.
-- You received this message because you are subscribed to the Google Groups DIYbio group. To post to this group, send email to diybio@googlegroups.com. To unsubscribe from this group, send email to diybio+unsubscribe@googlegroups.com. For more options, visit this group at https://groups.google.com/d/forum/diybio?hl=en
Learn more at www.diybio.org
---
You received this message because you are subscribed to the Google Groups "DIYbio" group.
To unsubscribe from this group and stop receiving emails from it, send an email to diybio+unsubscribe@googlegroups.com.
To view this discussion on the web visit https://groups.google.com/d/msgid/diybio/CAA0yOM58QSR2VT-zZqvdHQsuOYAXyGLoqR2C1fkFAQSNdU6x_Q%40mail.gmail.com.
0 comments:
Post a Comment